home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Collection of Tools & Utilities
/
Collection of Tools and Utilities.iso
/
comm
/
qm431_1.zip
/
QMODEM.MDF
< prev
next >
Wrap
Text File
|
1991-09-09
|
40KB
|
2,765 lines
* Copyright(C) 1991, The Forbin Project Inc.
* All rights reserved. Copying contents is illegal.
@Anchor 2400i Internal Half-card
2400
10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
^ATE1Q0M1X4V1S7=60^M
^AT&C1&D2&W^M
*Your 2400 baud modem is ready to go!
@AST 2X9600
19200
10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
$ Switch Settings: FRONT 1 2 3 4 5 6 7 8 9 10
$ U D D U D U U D * *
$
$ REAR 1 2 3 4 5 6 7 8
$ *=Not Used D D D U D U U *
^AT&F^M
^AT&C1&D2\J0\N3\Q3\V1&W^M
*Your AX9624c is now configured for 19200 baud operation. Be sure
*to set ALL your dialing directory entries to 19200 to get the
*best speed on all calls.
@AT&T Dataphone II 2212C (1200 baud)
1200
10
A^~T^~^M^~^~^M
^M^~^~ATT
^M
Answered
Not connected
Invalid number
No dial
Busy
$:^~^~q^~^M
$:^~^~q^~^M
0
0
1000
$ Switch Settings: INSIDE 1 2 3 4
$ C O O O
$ C=closed O=open
$
$ These are inside the case.
^M^~^~od^~^~^~y^~^~^~at^M^~^~^~^M^~^~^M
*Your Dataphone II is ready to go! Be sure to read your modem
*manual and double-check the setup.
*Note: Host mode operation is not supported at this time.
@ATI 2400etc (non V.42)
9600
10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F1^M
^AT&C1&D2&W^M
*Your ATI 2400etc modem is ready to go! You can set all of your
*dialing directory entries to 9600 baud and the modem will handle
*speed conversions for you. MNP operation has also been enabled.
*Remember to Exit/Save from SETUP to save these changes!
@ATI 2400etc/e & 2400etc/i (with V.42)
9600
10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F2^M
^AT&C1&D2&W^M
*Your ATI 2400etc modem is ready to go! You can set all of your
*dialing directory entries to 9600 baud and the modem will handle
*speed conversions for you. MNP operation has also been enabled.
*Remember to Exit/Save from SETUP to save these changes!
@ATI 9600etc/e V.32/V.42
38400
10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F2^M
^AT&C1&D2&W^M
*Your ATI 9600etc modem is ready to go! You can set all of your
*dialing directory entries to 38400 baud and the modem will handle
*speed conversions for you.
@Cardinal 2400 MNP
9600
10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^AT&C1&D2&T5\C1\J0\N3\Q3\V1\K3&W^M
*Your Cardinal 2400 MNP modem is ready to go! You can set your
*dialing directory entries to 9600 baud and the modem will handle
*speed conversions for you. MNP operation has also been enabled.
@Cermetek INFO-MATE 212A
1200
XY
210
U 1^M^~C 0^M
D 'T
'^M
A
B
X
N
V
^M
DTR
0
0
1000
$You must open the case to set the switches. Refer to your
$modem manual for this procedure.
$
$Switch settings: 1 2 3 4 5 6 7 8
$ ON OFF OFF ON ON OFF ON OFF
$
*Your Info-Mate 212A is ready to go! Be sure to read your modem
*manual and double-check the setup.
*Note: Host mode operation is not supported at this time.
@CompuCom Speedmodem
19200
10
AT&F2*H2&D2S10=30%C0H0
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
NO ANSWER
^M
DTR
RING
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
*Your SpeedModem is ready to go! You can set all of your dialing
*directory entries to 19200 baud and the modem will handle speed
*conversions for you.
@Digicom 9624LE / 9624PC V.32bis
38400
10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^AT*F3*E9&W^M
*Your Digicom modem is ready to go! You can set all of your
*dialing directory entries to 38400 baud and the modem will handle
*speed conversions for you.
@Digitan Hi*IQ ZX1896 2400 Fax Modem
2400
10
ATE1Q0V1X4&C1&D2S7=60S25=4^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
*Your 2400 baud modem is ready to go! Be sure to read your
*modem manual and double-check the setup.
@E*Tech Bullet PC2400MH MNP
9600
10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^AT&C1&D2&T5$C1$E2$F4$X1&W^M
*Your E*Tech 2400 MNP modem is ready to go! You can set your
*dialing directory entries to 9600 baud and the modem will handle
*speed conversions for you.
@E*Tech Bullet E9696M V.32 MNP
19200
10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^AT&C1&D2&T5$C1$E1$F4$S0$X5&W^M
*Your E*Tech 9696M modem is ready to go! You can set all of your
*dialing directory entries to 19200 baud and the modem will handle
*speed conversions for you.
@Everex 12e External (EV-936)
1200
10
ATE1F1H0M1Q0V1X4&C1&D2^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
NO ANSWER
^H
DTR
RING
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
1000
$ Switch Settings: 1 2 3 4 5 6 7 8 9
$ On Off Off Off Off On Off Off Off
*Your Everex 12e (EV-936) is ready to go! Be sure to read your
*modem manual and double-check the setup.
@Everex 24e External (EV-945)
2400
10
ATE1F1H0M1Q0V1X4&C1&D2^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
NO ANSWER
^H
DTR
RING
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
1000
$ Switch Settings: 1 2 3 4 5 6 7 8 9
$ On Off Off Off Off On Off Off Off
*Your Everex 24e (EV-945) is ready to go! Be sure to read your
*modem manual and double-check the setup.
@Everex Evercom 24+ MNP
9600
10
AT\C0\J0\K5\N3\Q0\V1V1E1Q0X4^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
NO ANSWER
^H
DTR
RING
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
*Your Everex Evercom 24+ is ready to go! Be sure to read your
*modem manual and double-check the setup.
@Everex EverFax 24/96
9600
10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
NO ANSWER
^H
DTR
RING
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^AT&F^M
^AT&T5\J0\N3\V1\X1%C1\Q3&W
*Your Everex EverFax 24/96 is ready to go! Be sure to read your
*modem manual and double-check the setup.
@Fastcomm FDX 2424 (MNP Class-5)
9600
10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
NO ANSWER
^M
DTR
RING
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
$All switches on the bottom of the modem should be in the
$OPEN (off) position.
^AT&F^M
^ATE1Q0M1X4V1S7=60^M
^AT&B1&C1&D2&G0&H1&I1&M6&W^M
*Your FDX 2424 modem is ready to go! Be sure to read your
*modem manual and double-check the setup.
@Fastcomm FDX 2496
9600
10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
NO ANSWER
^M
DTR
RING
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
$All switches on the bottom of the modem should be in the
$OPEN (off) position.
^AT&F^M
^ATE1Q0M1X4V1S7=60^M
^AT&B1&C1&D2&G0&H1&I1&M6&W^M
*Your FDX 2496 modem is ready to go! Be sure to read your
*modem manual and double-check the setup.
@Fastcomm FDX 9696 (V.32 & MNP-5)
19200
10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
NO ANSWER
^M
DTR
RING
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
$All switches on the bottom of the modem should be in the
$OPEN (off) position.
^AT&F^M
^ATE1Q0M1X4V1S7=60^M
^AT&B1&C1&D2&G0&H1&I1&M6&W^M
*Your FDX 9696 modem is ready to go! Be sure to read your
*modem manual and double-check the setup.
@Forval IM14400/SA14400 V.32bis (38400 baud)
38400
10
ATZ0^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^ATS25=0S7=60%E0\J0